Price
$147.99 – $163.99Price range: $147.99 through $163.99
Total
$147.99 – $163.99Price range: $147.99 through $163.99
Cylinder Sleeve Flex-Hone Tools
"Nitrolink" carries the popular bore sizes needed, so one of these Cylinder Sleeve Flex-Hone Tools can help make that job a little easier to deal with. They offer a quick, consistent "clean up" by removing peaks and imperfections on your cylinder walls for better performance! They're self-centering and self-aligning to the bore with each of the abrasive pads having independent suspension, allowing them to compensate accordingly to correct wear areas for a superior even surface finish. When ordering please use your actual cylinder inside diameter, as all Flex-Hones are produced over-sized and will adjust to work with your size sleeve.
Please specify bore size needed in the "options" menu below.
Price
$485.00 – $575.00Price range: $485.00 through $575.00
Total
$485.00 – $575.00Price range: $485.00 through $575.00
We offers a complete line of all Dan Olson Race Products!
Dan Olson BBC Aluminum Valve Covers
Attention all Big Block Chevy Race Teams! "Nitrolink" is always happy to help make your engine look as good as it performs with a pair of brand new Dan Olson BBC Aluminum Valve Covers. Just take a look at the tig welding and you'll see a quality product that's equipped with 3/8" size billet rails that were designed to help provide a flat secure seal even after repeated installation and removal. They can be ordered standard, or with rail oilers at a slight additional cost if you choose. And this style is sure to offer that clean, finished appearance you've been looking for!
Please note: Custom made to your exact specifications. Please call: (916) 425-1427 to order.
Deluxe Digital Leak Down Testers
If you're looking for a top quality tool with precision accuracy then consider one of these brand new Deluxe Digital Leak Down Testers to add to your racing operation! Loaded with all the extras you would expect in a top of the line tool, this model provides easy-to-read digital numbers that read within 1/2 of 1% percent accuracy making it much more accurate than traditional testers. It's the best way to check for bent or leaking valves, bad ring seal, or even leaking head gaskets. Both gauges feature rubber bumpers for extra added protection and are back lit for easy legibility and equipped with low battery indicators. Outfitted with a control inlet valve to avoid shock to the gauges when air is turned on, to help provide a more accurate reading, easier use and longer gauge life. It comes complete with either a 12mm, or 14mm spark plug connector and hose. And includes it's own protective storage case for a very nice package deal. Now you know exactly where to go for all the cool higher end racing components... Nitrolink!
Choose either 12mm, or 14mm spark plug size in the options menu below.
We offer a complete line of all Pit Pal products!
Deluxe Helmet Shelf
Nitrolink is excited to offer your race team top quality Pit Pal race trailer accessories for the exact same price as the manufacturer! And when it comes to keeping your race trailer organized and efficient, then a brand new Deluxe Helmet Shelf is sure to help keep your driver's gear and crew shirts out of the way and stored safely during transport! This one's made of durable aluminum and equipped with 2 helmet bays on the top, plus an extra added storage shelf underneath. A handy removable front hanger bar is located at the bottom for hanging clothing, tie-downs and more. And the underside provides an additional garment hanger if needed. Unit measures 28.5"W x 12"H x 15"D. And could work just as well in your race shop, or garage... Shop here 24/7 for all your Pit Pal needs! GoNitrolink.com
Helmet for display only.
Dial Indicator Kit for Valve Spring Tester
If you're thinking about purchasing one of the Bench Top Valve Spring Testers we sell, or already have one... Then check out one of these brand new Dial Indicator Kit for Valve Spring Tester that can be easily added for optimum precision accuracy. It's allows you to check your installed height, or coil bind while you're testing for spring pressure without having to do it old school by using a micrometer. It installs quickly with a very small amount of light grease and your 3/16" hex with a 7/16" open end wrench to set the stop. Check out all the other specialty pit tools available right here, designed specifically to make your job that much easier!
Valve Spring Tester (in photo) sold separately.
Digital Dash Cover - Racepak
Helping to keep one of your main on-board computer components safe is the only job this brand new Digital Dash Cover - Racepak was designed to do! This one works with the popular Pro 2 or Pro 3 early style digital dash. It comes complete with a replaceable clear top lens that not only helps protect your dash from fuel, hot oil, brake cleaner, or track debris. But also offers your crew chief optimum visibility for a clear look at real time data on the starting line. It's durable, light weight and easy to install. And commonly mounted on top of your air timer "tool box" if you're running a front engine dragster or funny car. Or, on the firewall under the roll cage if you're running a rear engine dragster (hardware not included). This item is definitely worth every penny and one of the best ways to help protect your expensive investment... All the cool components offered right here 24/7! GoNitrolink.com
Replacement Lenses also available.
Digital Dash Cover Lens
GoNitrolink.com is your one-stop shop for some of the coolest race parts on the planet... But, also their replacement parts as well! If you have one of our Racepak Digital Dash Covers, then it may be time to replace your scratched, worn out Digital Dash Cover Lens with a brand new one. Once you remove the protective covers seen in the photo, your crew chief will once again be able to see all your real time data on the starting line crystal clear once again. And not only are we going to make ordering 'em super easy. But also super affordable as well... Just click, pay and it's on the way!
Sold separately.
Digital Torque Wrench Tester
At the race track or back at the race shop, it's critical to be able to reach for a torque wrench that reads accurately every time you use it! Consistency wins races and this brand new Digital Torque Wrench Tester is the exact item needed to keep tabs on how consistent your torque wrench calibration is reading and when it's time to send out for service. This handy tool accommodates your 1/2" drive torque wrenches and has a push button conversion foot pounds to inches mode and a peak hold feature that saves your maximum reading. It's equipped with a back lit read out screen for night use and powers up using one standard 9-volt battery. Now you know where to go for all your specialty pit tools... Nitrolink!
Price: $695.00
Please call: (916) 425-1427 anytime to order.
Digital Valve Spring Tester
Efficiency at the track, as well as back at the race shop has always been a key component to winning races! And having access to the right tools to accomplish certain jobs quickly and easily makes all the difference! This brand new Digital Valve Spring Tester is sure to deliver everything you would expect, and then some... This quality unit is made of 6061 T-6 billet aluminum and equipped with 2" diameter plates that can handle almost any spring on the market and has a 5" travel capacity. The easy access controls on the front of the tester, along with the large, easy-to-read numbers on the back-lit screen makes it a breeze to run thru a set of springs in no time. It's capable of testing springs up to 1500 lbs; in 1 pound increments, with a digital travel readout in .001" increments. Equipped with a rotatable adjustable stop for fast measuring of open and closed spring pressures. And 3 mounting locations on the handle allow you to adjust the length for increased torque. The simple to use travel stop with 2 set screws is perfect for setting an exact position, allowing repeated testing at a specific installed spring height, or wide open lift (near coil bind). This unit is switchable from pounds to kilograms and operates on one 9V battery that's also included. Order one here today, then get ready to go to work!
Donovan Aluminum 565 C.I. Big Block Chevy
Brand new with zero laps!!! And equipped with all the best parts money can buy is exactly what you'll find right here with this Donovan Aluminum 565 C.I. Big Block Chevy that's being sold complete, turn-key and ready for showtime!!! No expense was spared in outfitting this Race Engine with everything needed to be competitive on the race track. And the great news is, it won't cost you anything close to the $50,000 bucks it cost to build it... So let's get to it!!!
About the Engine:
• New Donovan Aluminum 565 C.I. Big Block Chevy
• New Standard Deck, Water Block
• New Dart Pro 1 Cylinder Heads
• New Victory Titanium Intake & Exhaust Valves
• New Wiseco Pistons
• New GRP Aluminum Rods
• New Callies Crankshaft
• New MSD Crank Trigger System
• New Comp Cams Roller Camshaft
• New Isky Roller Lifters
• New Manton Pushrods
• New RCD Gear Drive
• New Jesel Shaft Rockers
• New Williams Valve Covers
• New Edelbrock Low Profile Manifold
• Enderle Birdcatcher
• Enderle Barrel Valve
• Enderle Fuel Pump
• MSD Ignition System
• Custom Zoomie Headers
• New Meziere Billet Flywheel
• New Meziere Heavy Duty Starter
• Dan Olson Custom Oil Pan
• And much more...
Don't miss this opportunity to acquire this turn-key race engine with brand new components for you're very own!!! This complete package is available immediately and sure to save it's new owner thousands of dollars not having duplicate everything here. Then countless hours not having to put it all together from the ground up... Now you're ready to go on tour with the right equipment for the new 2025 season!!!
Priced to move at: Only $31K OBO. All serious reasonable offers considered.
Double End AN Wrench Set - 7 Piece
"Nitrolink" also offers this style Double End AN Wrench Set - 7 Piece for a hassle-free environment at your race shop the next time you decide to assemble hose ends, or check all the lines on your race car. This 7 piece set, (3 AN to 20 AN) is made of 6061-T6 billet aluminum. The contoured edges make them comfortable to use. And the shorter design length helps to prevent over-tightening your hose ends. All wrenches are anodized, color coded and numbered for quick easy identification. And the perfect addition to any pit tool box!
Price
$168.95 Original price was: $168.95.$118.95Current price is: $118.95.
Total
$168.95 Original price was: $168.95.$118.95Current price is: $118.95.
Double End Pro Series AN Wrench Set
The exact same quality, strength and durabilty is offered here with less wrenches to carry! This anodized Double End Pro Series AN Wrench Set is made by XRP and works with the swivel nuts on hose ends. Each of the (4) wrenches are color coded so you know exactly what wrench to reach for to get the job done quickly. And the fully radiused edges offers a comfortable grip second to none. This set is made from heat treated 6061 aluminum alloy for lasting performance. And includes sizes: (-3, -4) ( -6, -8) (-10, -12) (-16 & -20). Now you know exactly where to go for all your specialty pit tool needs! GoNitrolink.com
